5 views (last 30 days)
Show older comments
Mehdi Jaiem on 21 Jan 2021
Commented: Mathieu NOE on 21 Jan 2021
Accepted Answer: Star Strider
Open in MATLAB Online
Hello everyone,
I intend to use freqz() function I need to plot the magnitude for different border frequencies. But first I need to determine the cut off frequencies.
I used this code but which seems to not give me even a close response to this
%% INitializing Matlab Environment
close all;
clc;
clearvars;
%% 1.1
b=log10(8000);%stop frequency and 100Hz is the pass frequency
yc1=logspace(2,b,23);
yd=stem(yc1);
grid on
xlabel('Borders','FontSize',12);
ylabel('F (Hz)','FontSize',12);
set(gca,'YScale', 'log')
%%
m={};
n={};
h={};
ph={};
j={};
fs=21e3 %sampling frequency
for i= 1:1:23
[u,o] = butter(1,[2*100/fs, (2*yc1(i))/fs],'bandpass');
m{i}=u;
n{i}=o;
%freqz(m{i},n{i});
[h{i},ph{i}]=freqz(m{i},n{i});
figure
subplot(2,1,1)
hold on
plot(ph{i},20*log10(abs(h{i})));
end
hold off
grid
set(gca,'XLim',[0 1e4],'XTick',10.^(0:4),'YLim',[-12 0],'YTick',-12:2:0,'XScale', 'log')
Any Idea on what I am missing ?
0 Comments Show -2 older commentsHide -2 older comments
Show -2 older commentsHide -2 older comments
Sign in to comment.
Sign in to answer this question.
Accepted Answer
Star Strider on 21 Jan 2021
Open in MATLAB Online
Put the figure call before the loop, and remove the subplot call:
figure
hold on
for i= 1:1:23
[u,o] = butter(1,[2*100/fs, (2*yc1(i))/fs],'bandpass');
m{i}=u;
n{i}=o;
%freqz(m{i},n{i});
[h{i},ph{i}]=freqz(m{i},n{i});
plot(ph{i},20*log10(abs(h{i})));
end
hold off
This does not exactly produce the plot you posted, however it will get you closer.
I leave the other details to you.
2 Comments Show NoneHide None
Show NoneHide None
Mehdi Jaiem on 21 Jan 2021
Direct link to this comment
https://support.mathworks.com/matlabcentral/answers/723128-plotting-multiple-magnitudes-in-one-plot#comment_1276758
Edited: Mehdi Jaiem on 21 Jan 2021
Thank you it solves at least the multiplot issue !
Star Strider on 21 Jan 2021
Direct link to this comment
https://support.mathworks.com/matlabcentral/answers/723128-plotting-multiple-magnitudes-in-one-plot#comment_1276768
As always, my pleasure!
Sign in to comment.
More Answers (1)
Mathieu NOE on 21 Jan 2021
Open in MATLAB Online
hello
according to the picture, your code needed a revision, see below
the bandwith of your filters (BW) should be proportionnal to the center frequency to have identical roll off curves when plotted in log axis
you can test with a fixed constant bandwith , it's no the right option
hope it helps !
%% INitializing Matlab Environment
close all;
clc;
clearvars;
%% 1.1
b=log10(8000);%stop frequency and 100Hz is the pass frequency
BW = 100; % fixed bandwith (Hz)
yc1=logspace(2,b,23);
yd=stem(yc1);
grid on
xlabel('Borders','FontSize',12);
ylabel('F (Hz)','FontSize',12);
set(gca,'YScale', 'log')
%%
fs=21e3 %sampling frequency
for i= 1:1:23
BW = 100; % fixed bandwith (Hz) : NO !!!
% BW should be proportionnal to center frequencies (not fixed)
BW = yc1(i)/5;
f_low = yc1(i) - BW/2;
f_high = yc1(i) + BW/2;
[B,A] = butter(1,[f_low, f_high]*2/fs,'bandpass');
freq = logspace(log10(f_low/4),log10(f_high*4),100),
[h]=freqz(B,A,freq,fs);
figure(2)
hold on
semilogx(freq,20*log10(abs(h)));
end
hold off
grid
set(gca,'XLim',[0 1e4],'XTick',10.^(0:4),'YLim',[-12 0],'YTick',-12:2:0,'XScale', 'log')
2 Comments Show NoneHide None
Show NoneHide None
Mehdi Jaiem on 21 Jan 2021
Direct link to this comment
https://support.mathworks.com/matlabcentral/answers/723128-plotting-multiple-magnitudes-in-one-plot#comment_1276858
Open in MATLAB Online
Awesome thank you!
I have to review some notons then since I am new to this topic.
But there are two ine that I did not understand:
BW = yc1(i)/5; %why did you divide by 5
freq = logspace(log10(f_low/4),log10(f_high*4),100) % what is the perpose of 100?
semilogx(freq,20*log10(abs(h))); % I read about semilogx but I did not understand it. why not plot ?
Mathieu NOE on 21 Jan 2021
Direct link to this comment
https://support.mathworks.com/matlabcentral/answers/723128-plotting-multiple-magnitudes-in-one-plot#comment_1277028
BW = yc1(i)/5; %why did you divide by 5
bandwith is a fraction of center frequency , the higher the division factor, the narrower the filter ; just adapt to your own needs
freq = logspace(log10(f_low/4),log10(f_high*4),100) % what is the perpose of 100?
this is the length we want for freq vector; try another value , like 10, and see the plot being not so smooth
semilogx(freq,20*log10(abs(h))); % I read about semilogx but I did not understand it. why not plot ?
try plot to see the difference
Sign in to comment.
Sign in to answer this question.
See Also
Categories
Signal ProcessingSignal Processing ToolboxDigital and Analog FiltersAnalog Filters
Find more on Analog Filters in Help Center and File Exchange
Tags
- freqz
- bandpass
Community Treasure Hunt
Find the treasures in MATLAB Central and discover how the community can help you!
Start Hunting!
An Error Occurred
Unable to complete the action because of changes made to the page. Reload the page to see its updated state.
Select a Web Site
Choose a web site to get translated content where available and see local events and offers. Based on your location, we recommend that you select: .
You can also select a web site from the following list
Americas
- América Latina (Español)
- Canada (English)
- United States (English)
Europe
- Belgium (English)
- Denmark (English)
- Deutschland (Deutsch)
- España (Español)
- Finland (English)
- France (Français)
- Ireland (English)
- Italia (Italiano)
- Luxembourg (English)
- Netherlands (English)
- Norway (English)
- Österreich (Deutsch)
- Portugal (English)
- Sweden (English)
- Switzerland
- Deutsch
- English
- Français
- United Kingdom(English)
Asia Pacific
- Australia (English)
- India (English)
- New Zealand (English)
- 中国
- 日本Japanese (日本語)
- 한국Korean (한국어)
Contact your local office